Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- projekte:6cmtrv:start [2025/12/16 00:11] – angelegt yc
+++ projekte:6cmtrv:start [2025/12/16 01:35] (aktuell) – yc
@@ Zeile 4: / Zeile 4: @@
 Objectives:
   * Output power > 1 W
-  * Receive noise figure < 3 dB NF
+  * Receive noise figure < 2 dB NF
   * Integrated IF and RF transmit/receive switches
   * Integrated stable and clean local oscillator
+**[[https://git.loetlabor-jena.de/yc/6cm_trv|design repository (Gitlab)]]**
 ===== Preface =====
 For many years low-cost LNBs enable people to have very easy access to 10 GHz reception. It's size and ease of use makes it enjoyable to use in many situations. For the 6 cm band no comparable solution is known.
@@ Zeile 13: / Zeile 15: @@
 Low-cost and easy to handle components are available to modern radio enthusiasts. An All-in-one transverter combines them with modern PCB technology.
-==== Concept ====
+===== Concept =====
 A block diagram of the transverter is shown in the figure below.
@@ Zeile 27: / Zeile 29: @@
 An on-board controller is used for managing state transitions of the transverter. After power-up the OCXO will heat-up. All other components are still off until the target temperature is reached and the current consumption went down. The controller measures the current on the power rail and will initialize the local oscillator followed by switching to receive mode after reaching the threshold current.
 Via the control port the transceiver can request to switch to transmit mode. During initialization and receive mode transceiver's output is blocked by the transmit inhibit signal. After switching to the transmit path the transceiver is allowed to transmit. This guarantees a safe operation for all components.
+===== Implementation =====
+Like in previous projects ([[..:lofourx:start|10 GHz Multiplier]], [[..:3cmbeacon:start|10 GHz Beacon]]) CPWG transmission lines on a four-layer stackup are used. The RF design is based on the well-characterized coaxial/PCB transition and uses a complete coplanar transmission design to interface to all QFN components in GND-signal-GND style for continuous impedance behavior. For the large pads of the bandpass filters an individual footprint was designed and simulated for proper 50 Ohm interfacing on the thin substrate used. As all other components are internally matched no further on-board matching is required.
+{{:projekte:6cmtrv:6cmtrv_pcb.jpg?400|}}
+In transmit mode 7.5 watts of heat is dissipated. For proper heat sink the PCB is directly connected to the housing with attached heatsink.
+{{:projekte:6cmtrv:6cmtrv_front.jpg?400|}} {{:projekte:6cmtrv:6cmtrv_back.jpg?400|}}
+Front and back panels are low-cost PCBs with black solder mask and white silk screen. LEDs are placed on the back panel to show the current state state.
+^ State ^ RX ^ TX ^ HT ^ PWR ^
+| heating | off | off | blinking \\ blink speed depends on OCXO current | off |
+| receiving | on | off | on | all good \\ LO locked and power good |
+| transmitting | off | on | on | high power \\ on for current power above 1 W |
+===== Testing =====
+The first prototype was characterized after final assembly. The maximum output power is 29 dBm with 100 mW input power and a noise figure of 3.1 dB is achieved. With 1 dB of switch loss and additional transmission line attenuation the results seem reasonable but noise figure needs some investigation, 1.6 dB was intended.
+The phase noise in transmit mode is surprisingly good without any optimization:
+{{:projekte:6cmtrv:6cmtrv_pn.png|}}